Huazhao Refrigeration Equipment Blog

1. Important equipment components exhibit scaling That is to say, due to improper maintenance and maintenance of the equipment, the operation efficiency is low. For example, when the condenser of the refrigeration unit exhibits severe fouling, it will affect the heat exchange effect and cause the overall operational efficiency of the equipment to be low. In addition to the condenser, which is easy to exhibit fouling, such as the transmission mechanism presents a serious wear phenomenon, that is to say, in the long-term operation process, the centrifugal impeller, the transmission mechanism, the upper and lower speed bearings and other important The wear parts of the mobile parts are worn out, so it is easy to incur the lack of efficiency of the equipment. 2. Has a higher load in operation Since the Water  Cooled Screw Chiller  often causes the equipment to stop overloading during consumption, under normal conditions, the load operation rate of the refrigeration equipment is pref

As a  Water Cooled Screw Chiller Supplier , we will discuss Is the insulation effect of the glass wool felt good. 1.  Screw Chiller  chemical method. At present, the cooling water system of large-scale water coolers adopts a chemical method and participates in scale inhibitors, corrosion inhibitors, bactericides and supporting cleaning agents in cooling water to form a complete set of cooling water disposal technology. Design reference for large air conditioning cooling water disposal. The principle of chemical disposal is revealed. Since the scale inhibition can ensure the heat transfer effect, the corrosion inhibitor and the bactericidal algicide can reduce the corrosion of the equipment and prolong the life of the equipment, and thus has been receiving the attention of countries all over the world. Large foreign water disposal companies have taken this technology as the first focus. 2. Screw chiller dosing method: This method was applied to hot water boilers and ship mooring

The  Water Cooled Screw Chiller Machine  rate is usually controlled by the pressure drop of the cooling water entering and leaving the condenser. Since the cooling water valve cannot be excessively opened excessively, if it is desired to increase the cooling water amount and reduce the condensing pressure, the screw type cold water is reached and lowered. The method of energy consumption of the machine is difficult to complete. To reduce the power consumption of the screw chiller, it is necessary to reduce the condensing temperature of the screw chiller as much as possible. There are two measures that can be taken: 1. Reduce the inlet water temperature of the  Water Cooled Screw Chiller  condenser: However, the inlet water temperature of the screw chiller condenser depends on the atmospheric temperature and relative humidity, which is affected and limited by changes in natural conditions. 2. Increase the cooling water volume of the  screw chiller : Although this method is simple

Here is  Water Cooled Screw Chiller Supplier  talking about Analysis of the causes of noise generated by the operation of chiller manufacturers. If you have any idea about  Water Cooled Screw Chiller Price , welcome to contact us and discuss. Noise is common in the operation of industrial equipment. There are many reasons for noise. It may also be caused by some environmental problems in the installation. When noise is generated, we must first confirm the cause, and whether it is internal components. The problem is presented because if the problem is presented and the replacement or repair is not stopped in time, the chiller will not work properly. The environment and location of the device can cause noise problems, and if it is in a relatively small environment, the noise will be "amplified". A small environment will make the normal operation sound louder, and it will sound beyond the normal operation. It is recommended that whether it is an air-cooled machine or

An  Auto Water Cooled Chiller  is a machine that removes heat from a liquid via a vapor-compression or absorption refrigeration cycle. This liquid can then be circulated through a heat exchanger to cool air or equipment as required. As a necessary byproduct, refrigeration creates waste heat that must be exhausted to ambient or, for greater efficiency, recovered for heating purposes. Concerns in the design and selection of chillers include performance, efficiency, maintenance, and product life cycle environmental impact. Water Cooled Chiller Machine  systems have these important elements: Compressor : Provides the energy system. Condenser : Rejects heat gained by the gas using ambient air or cooling tower water to condense the gas back to a liquid for use again by the evaporator. The condenser is a heat exchanger, which dissipates the heat absorbed in the evaporator. System Expansion : The liquid refrigerant enters the expansion device which reduces pressure. By reducin

Today we  Water Cooled Screw Chiller Seller  come to summarize How to reduce transportation cost and improve the efficiency of cold chain logistics. With the rapid development of China's fresh-keeping technology, the development environment and infrastructure conditions of cold chain logistics have been continuously improved, which has led to the rapid development of cold chain logistics. At this stage, cold chain logistics is restricted by factors such as logistics infrastructure capacity and logistics technology. As a result, the cold chain logistics transportation efficiency is low, the corrosion rate is high, and the cost is high, which has become a direct problem faced by all cold chain logistics enterprises. How can enterprises improve the circulation efficiency of cold chain logistics under existing conditions and reduce the key damage rate and logistics cost of logistics and transportation? How to reduce transportation cost and improve the efficiency of cold chain lo